Happymodel CINE8 85mm Brushless Cinewhoop DIY KIT
This Kit is very easy to build , no solder work any more, just assemble then plug and play .
Very cheap but equipped with high-performance and stable components. The frame is formed by high-precision TPU 3D printing, fixed with carbon fiber board and the use of integral foam to prevent collision. Every FPV pilots could enjoy the fun of building their own FPV Cinewhoop.
Features:
No Solder work need and easy to build
Very reliable and resistant to drops
Stable and smooth flying
Insta360 fixed mount ready
Smooth and powerful
Diversity SPI Receiver compatible Frsky/S-FHSS/Redpine protocol
Specifications：
Brand Name: Happymodel
Item Name: Cine8
Wheelbase: 85mm
Size: 145mmx140mmx23mm
Weight: 73g(without battery)
Weight: 99g(with Insta360)
Receiver option:
Internal SPI Frsky version (Compatible with Frsky ACCST D8/D16, S-FHSS, Redpine)
External Flysky Fli14+ receiver version(Compatible with Flysky AFHDS-2A protocol radio)
External Speki+ receiver version(Compatible with Spektrum DSM2/DSMX protocol radio)
External TBS Crossfire Nano receiver version
Motor
Mode: EX1202.5 KV8000
Configu-ration:9N12P
Stator Diamter:12mm
Stator Length:2.5mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.*Len):Φ14mm*14.5mm
Weight(g):4.4g
No.of Cells(Lipo):2-3S
Propellers
Material:PC
Weight:0.91g
Pitch:2in
Props Dia:50.3mm
Center Thickness:4.5mm
Center Hole Dia:1.5mm 3 holes
Flight controller
(Frsky SPI RX version) CRAZYBEEF4 V3.1 FC Firmware target: CrazybeeF4FR
(S-FHSS SPI RX version) CRAZYBEEF4 V3.1 FC Firmware target: CrazybeeF4FR
(Redpine SPI RX version) CRAZYBEEF4 V3.1 FC Firmware target: CrazybeeF4FR
(External Flysky Fli14+ RX version) CRAZYBEEF4 V3.1 FC Firmware target: CrazybeeF4FR
(External Speki+ RX version) CRAZYBEEF4 V3.1 FC Firmware target: CrazybeeF4FR
(External TBS CRSF NANO version) CRAZYBEEF4 V3.1 FC Firmware target: CrazybeeF4FR MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 2-4S battery input (DC 2.9V-8.7V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5V 1A BEC
Onboard 4in1 ESC
MCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Current: 12A continuous peak 15A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: F_H_40_REV16_8.HEX
Default protocol: DSHOT600
Onboard Frsky SPI D8 receiver Version
CC2500 Hardware
Compatible with FrskyD FrskyX Frsky_X_LBT SFHSS REDPINE protocol
Channels: 8ch
Failsafe support
Diversity 2.4G receiver system
No ground interference: above 300meter
External Flysky Fli14+ receiver
Channel: 14
Protocol: AFHDS-2A
2.4G Mode: The second generation of an enhanced version of the automatic FM digital system
Antenna Length: 50mm (single antenna)
Input Power: 4.0-6.5V DC
Weight: Only 1g
Size: 19.5mm*12mm*5mm
Color: Black
Signal Output: IBUS
RSSI Output: Channel14
No ground interference: >500m
External Speki+ receiver
Dimension: 20mm*12.4mm*5mm
Support protocol: DSM2/DSMX
Output Signal configuration: SRXL(Set Spektrum2048/SRXL for the serial receiver provider)
Antenna connector: I-PEX MHF3
Antenna length: 70mm
Input voltage: 3.6v~13v
Input current: 100ma
Channels: Max12ch(usually channel 12 is used for RSSI)
External TBS CRSF Nano receiver
Original TBS CROSSFIRE Receiver ,CRSF Protocol , Official TBS transmitter compatible
5.8G 400mw VTX Output power: 25mw~400mw switchable
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 400mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band
SmartAudio ready
Caddx ANT 1200tvl camera
Image Sensor: 1/3" CMOS Sensor
Horizontal Resolution: 1200 TVL
TV System: NTSC or PAL
IMAGE: 16:9 or 4:3
Synchronization: Internal
Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
S/N Ratio : >52dB (AGC OFF)
Video Output: CVBS
Lens: 1.8mm
Min. Illumination:
[email protected]
Auto Gain Control: YES
BLC: YES
WDR: Global WDR
DNR: 3D DNR
Dimensions: 14*14mm(with bracket to 19*19mm)
Wide Power Input: DC 3.7-18V
Work Temperature: -20℃~+60℃
Weight: 2g (N.W.)
